The specified slider id does not exist.
Snap-In Electrolytic Capacitors ▏85℃ 2,000Hrs ▏CAIB
Snap-in & Lug 2000 Hrs, 85°C
Fail-Safe, will fail open without flame if excessive voltage is applied
RoHS Compliant
Спецификация
| Items | Performance | |||||||
| Пашазын Температур Диапазон | -40°C ~ +85°C | |||||||
| Правам Тема | +20% (at 120Hz, 20°C) | |||||||
| Идым Утечка (at 20°C) | I = 0.02CV or1.5 mA whichever is smaller (after 5 минут) Where, C= rated capacitance in µF. V= rated DC working voltage in V. | |||||||
| Энергопотеря Коэффициент (Tan at 120Hz, 20°C) | Номинальный Напряжений | 200 | 250 | 400 | 450 | |||
| Tan (max) | 0.15 | 0.15 | 0.20 | 0.20 | ||||
|
Low Temperature Characteristics (at 120Hz) |
Impedance ratio shall not exceed the values given in the table below. | |||||||
| Rated Vo | ltage | 200 | 250 | 400 | 450 | |||
| Impedance
Ratio |
Z( | -25°C)/Z(+20°C) | 4 | 4 | 8 | 8 | ||
| Z( | -40°C)/Z(+20°C) | 8 | 10 | 18 | 20 | |||
|
Load Life Test |
Test Time | 2,000 Hrs | ||||||
| Йоҥгытшо Вашталт | Within +20% of initial value | |||||||
| Энергопотеря Коэффициент | Шагал 200% of specified value | |||||||
| Идым Утечка | Within specified value | |||||||
| * The above specifications shall be satisfied when the capacitors are restored to 20°C after
the rated voltage applied for 2,000 hrs at 85°C |
||||||||
|
Shelf Life Test |
Test Time | 1,000 Hrs | ||||||
| Йоҥгытшо Вашталт | Within +20% of initial value | |||||||
| Энергопотеря Коэффициент | Шагал 150% of specified value | |||||||
| Идым Утечка | Within specified value | |||||||
| * The above specifications shall be satisfied when the capacitors are restored to 20°C after
exposing them for 1,000 hrs at 85°Cwithout voltage applied. The rated voltage shall be applied to the capacitors before the measurements (Refer to JIS C 5102) |
||||||||
|
Ripple Current & Frequency Multipliers |
Freq. (Гц)
W. Вуйсавырныш. (Вуйсавырныш) |
50/60 |
120 |
300 |
1K |
10K
up |
||
| Multiplier | 0.8 | 1.0 | 1.1 | 1.3 | 1.4 | |||
| Ripple Current &
Temperature Multipliers |
Temperature
( С ) |
40 | 60 | 70 | 85 | |||
| Multiplier | 1.8 | 1.4 | 1.2 | 1.0 | ||||
|
Safety Fundtion Test Conditions |
1. DC reverse voltage test:
The capacitor is shall be connected in reverse polarity, and applied under specified working voltage. |
|||||||
| 2. DC over voltage test:
The rated voltage of 1.2 times shall be applied to the capacitor. |
||||||||
| Other Standards | JIS C 5101-4 | |||||||
SNAP-IN TERMINAL TYPE
PART NUMBER EXAMPLE
Ойыртем
◆ Snap-in & Lug 2000 Hrs, 85°C
◆ Fail-Safe, will fail open without flame if excessive voltage is applied
◆ RoHS Compliant
