Ceramiczny kondensator trymerowy | 6Mm | CHCA
CECHY
◆OPERATINGTEMPERATURE RANGE: -25℃ to +85℃
◆RATED WORKING VOLTAGE: 100VDC
◆WITHSTANDING VOLTAGE: 110VDC 220VDC
◆SOLDERING TEMPERATURE: 250 ± 5℃
Aplikacje
Niniejsze specyfikacje dotyczą ceramicznych kondensatorów trymerowych z ceramicznym dielektrykiem, which are used for the electric and electronic apparatus and communication equipments.
Numer części
The part number consists of category, dimension , temperature characteristics and maximum nominal
Pojemność：
CHCA 3R0 2A R
( A ) ( B ) 3 ( C )
(A) Szereg
(B) Maximum nominal capacitance : PF unit in 3 digits (The1st and 2nd figures
indicate the significant figures, but the 3rd indicates the number of naught.)
( C ) Adjusting types : R (Reverse Type) or Blank (Normal Type)
- Ratedvoltage : 100VDC
- Temperaturerange : -25℃to +85℃
- Testcircumstance :Test should be done at 20℃ with relative humidity at 65%. Jednakże, subjected to special requirement,the ideal range should be within ±5℃ and humidity from 45℃to 85℃
Electrical Characteristic
- CapacitanceDrift After Adjustment
Rotation shall be made for 5 cycles for 180°at a rate of 20 r/mm, a capacitance value difference woul d be found immediately. Once the shaft is stopped at the position of the maximum capacit- ance value after 24 hours later. The specification range should be within 5pF, 10pF ± 1.5% and 30pF ± 2%.
- TemperatureCharacteristics
When measured the capacitance at 1MHz±10%, it reached the heat balance at each temperature changed to
.+20℃to -25℃with adjusting to 80%~90% of the maximum capacitance, the capacitance change is based on the capacitance at +20℃ of 2nF, stage of changing the temperature as above.
- Q(Quality factor)
When measured at 20℃, 0.5V to 5V, 1MHz and maximum capacitance , the Q values are l isted in the attached specification.
- Opór izolacji
When applied 100VDC between terminals for 1 minute at the maximum capacitance, the insulation resistance shall be more than 10,000M.
- WithstandingVoltage
There is no abnormality after applied 220VDC (1ess than 5mA) Do 5 seconds between the terminals.
Structure and mechanical characteristics
- Configurationand Dimensions
Please refer to the attached drawings.
- Strengthof Terminals
When applied a power to the terminals to any direction slowly and kept at 0.5 kg for 10 towary drugiej jakości, the terminals shall not be loosen or broken mechanically.
- Torque
The torque test should be done at least for l round tuning from 35gf.cm to 100gf.cm for the Normal Type, or 15gf. cm to 100gf.cm for the Reverse Type . Please note that it might cause the torque will decrease against the rotation increase.
- Lutowalność
When dipped the terminals into the soldering pot at 255℃±5℃ for 2±0. 5 towary drugiej jakości. There is almost 75% of the total dipped surface are covered with the new solder.( Caution: Keep the soldering conditions as above. If the soldering conditions are not suitable ( excessive t ime, excessive temperature and etc.), i t’s performance will be seriously deviated.
Color Code
Please refer to the color code in the attached specifications.
6mm Ceramic Trimmer Capacitors
| Part No. | Pojemność(pF) | Q(1MHz, Cmax) | Temp.Coeff ppm/℃ | Napięcie znamionowe | Withstanding Voltage |
Color Code |
||
| Min | Maks | |||||||
| CHCA3R02A(R) | 1.3maks | 3 | +50%-0% |
500 min |
NPO±200 | 100Vdc | 220Vdc | Blue |
| CHCA5R02A(R) | 1.5maks | 5 | +50%-0% | NPO±250 | 100Vdc | 220Vdc | Blue | |
| CHCA7R02A(R) | 2.0maks | 7 | +50%-0% | NPO±250 | 100Vdc | 220Vdc | Blue | |
| CHCA1002A(R) | 3.0maks | 10 | +50%-0% | N 450±300 | 100Vdc | 220Vdc | White | |
| CHCA2002A(R) | 5.0maks | 20 | +50%-0% | N 750±300 | 100Vdc | 220Vdc | Red | |
| CHCA3002A(R) | 6.0maks | 30 | +50%-0% | N 1000±500 | 100Vdc | 220Vdc | Green | |
| CHCA4002A(R) | 7.0maks | 40 | +50%-0% | 300 min | N 1200±500 | 100Vdc | 220Vdc | Yellow |
| CHCA5002A(R) | 10.0maks | 50 | +50%-0% |
200 min |
N 1200±500 | 100Vdc | 220Vdc | Brown |
| CHCA6002A(R) | 12.0maks | 60 | +50%-0% | N 1200±800 | 100Vdc | 220Vdc | Brown | |
| CHCA7002A(R) | 14.0maks | 70 | +50%-0% | N 2200±800 | 50Vdc | 110Vdc | Brown | |
| CHCA9002A(R) | 25.0maks | 90 | +50%-0% | N 2200±800 | 50Vdc | 110Vdc | Brown | |
| CHCA1212A(R) | 35.0maks | 120 | +50%-0% | N 2200±800 | 50Vdc | 110Vdc | Brown | |
WSTĘP
These specification are applied to ceramic trimmer capacitor with the ceramic dieletric ,which are used for the electric and electronic apparatus and communication equipments.
